The E2 error on your Morphy Richards air fryer can appear when you’re about to start cooking or while the appliance is already running. In some cases, the air fryer may stop heating completely, leaving you wondering what went wrong.
This error commonly indicates a problem with the temperature sensor or electronic control system. Understanding the possible causes can help you identify the fault and decide whether a simple check or professional repair is needed.

What Does Error E2 Mean on a Morphy Richards Air Fryer?
On certain Morphy Richards air fryers, error E2 indicates a short circuit involving the temperature sensor or printed circuit board (PCB). However, the exact meaning can vary depending on the model.
The temperature sensor monitors the heat inside your air fryer and sends readings to the control board. The board uses this information to regulate the heating element and maintain your selected cooking temperature.
If the sensor or its electrical circuit develops a fault, the control board may receive incorrect information. As a result, the appliance may display E2, stop heating, or refuse to start a cooking cycle.
Some models also display E1 for temperature sensor problems, but the two codes don’t necessarily indicate the same fault. Checking your model’s instruction manual will help you understand the specific warning.
Morphy Richards Air Fryer Error E2: Common Causes
Several electrical faults can trigger the E2 warning. The most likely causes involve the temperature sensing system, its connections, and the electronic control board.
1. Faulty Temperature Sensor
A damaged temperature sensor is one possible reason your Morphy Richards air fryer displays E2.
The sensor helps the appliance monitor cooking temperatures. If it develops an internal short circuit, the control board may receive readings outside its expected range and display an error.
Sensor failure can occur because of electrical damage, component deterioration, or excessive heat exposure.
You may notice E2 immediately after switching on the appliance or during cooking. However, these symptoms alone cannot confirm that the sensor is defective.
2. Damaged Sensor Wiring
The temperature sensor connects to the control board through electrical wiring. If these wires become damaged, the signals reaching the board may be affected.
Heat exposure, damaged insulation, or physical wear can sometimes cause electrical conductors to make unintended contact. This can create a short circuit.
A wiring problem may cause E2 to appear repeatedly or intermittently.
Because the affected wires are inside the appliance, identifying the fault generally requires professional inspection. Opening the housing yourself can expose you to dangerous electrical components.
3. Moisture Inside the Electrical Housing
Liquid entering the air fryer’s electrical housing can interfere with sensitive electronic components.
This may happen after an accidental spill or when water reaches areas that shouldn’t become wet during cleaning.
If moisture reaches the sensor connections or control board, it can potentially create an electrical fault.
You might suspect moisture damage if E2 appeared shortly after a spill or improper cleaning. However, the error doesn’t confirm that moisture is responsible.
If you believe water has entered the electrical housing, unplug the appliance and avoid using it until a qualified technician has checked it.
4. Faulty Control Board
The electronic control board manages the air fryer’s heating and temperature monitoring functions.
If a component in its temperature sensing circuit fails, the board may incorrectly interpret the sensor’s electrical signal or detect a short circuit.
This can trigger E2 even when the temperature sensor itself is working properly.
A control board fault may be suspected when the error continues after a safe restart. However, professional testing is necessary to distinguish it from a sensor or wiring problem.
Morphy Richards Air Fryer Error E2: DIY Fixes
A few safe checks can help you assess the problem before arranging repairs. Since E2 may indicate an internal electrical fault, avoid opening the appliance or attempting to repair its electronic components yourself.
1. Switch Off and Unplug the Air Fryer
Start by switching off your Morphy Richards air fryer and disconnecting it from the electrical outlet.
If it was operating when E2 appeared, allow it to cool completely before handling the removable components.
Pay attention to unusual smells, visible damage, or signs of overheating. If you notice smoke, sparks, or a burning smell, don’t attempt to restart the appliance.
Disconnecting the power prevents further operation while you decide what to do next.
2. Try a Power Restart
A simple restart may clear a temporary electronic error, although it won’t repair a damaged temperature sensor or control board.
To perform a restart safely, follow these steps.
- Unplug the air fryer from the wall outlet.
- Allow it to cool completely.
- Check that the plug and appliance exterior are dry and undamaged.
- Reconnect the air fryer if there are no signs of electrical damage.
- Check whether E2 appears again without starting a cooking cycle.
If the warning returns, unplug the appliance and stop troubleshooting.
Even if E2 disappears, contact the manufacturer for guidance before cooking again. An intermittent electrical fault may temporarily stop displaying an error.
3. Inspect the Power Cord and Plug
Check the air fryer’s power cord and plug for visible damage.
Look for cracked insulation, exposed wires, burn marks, or melted plastic. Also, examine the wall outlet for discoloration or other signs of damage.
Although a damaged power cord isn’t a confirmed cause of E2, it can create a separate electrical hazard.
If you find any damage, don’t use the appliance. A qualified professional should assess the affected component and determine whether replacement is necessary.
4. Check for Moisture and Clean Accessible Parts
If the error appeared after cleaning or a liquid spill, inspect the accessible areas for moisture.
Once the appliance is unplugged and completely cool, remove the cooking basket or bowl according to your model’s instructions.
Clean the removable accessories using the method recommended by Morphy Richards. Wipe permitted exterior surfaces with a slightly damp cloth and dry everything thoroughly.
Avoid spraying water into ventilation openings or allowing liquid to reach the control panel.
If moisture has entered the electrical housing, don’t attempt to dry the internal circuits with a hair dryer or another heating appliance. Have the unit professionally assessed instead.
5. Check Your Air Fryer’s Model and Manual
Morphy Richards manufactures different air fryer models, and their error codes aren’t always explained in exactly the same way.
For example, the MRAFG55BK instruction manual identifies E2 as a short circuit involving the thermal sensor or PCB. Other models may describe E2 more generally as a circuit fault.
Find your model number on the appliance’s rating label or original packaging. Then consult the matching instruction manual for the recommended response.
If your air fryer is still under warranty, contact Morphy Richards or the appropriate regional support provider before arranging repairs.
6. Contact a Qualified Appliance Technician
If E2 continues appearing, your air fryer may need professional diagnosis.
A qualified technician can check whether the fault involves the temperature sensor, internal wiring, or control board.
Depending on the findings, replacing a damaged component may restore normal operation. However, some models may not have readily available replacement parts.
If your appliance is still covered by warranty, contact the manufacturer or retailer first. For an older unit, compare the repair cost with the price of a replacement.
Don’t continue using an air fryer that repeatedly displays E2. An unresolved electrical fault may affect its safe operation.
Wrap-Up
The Morphy Richards air fryer E2 error commonly points to a temperature sensor or electronic circuit fault on models that use this code. Although a power restart and basic external checks may help identify obvious problems, internal electrical faults usually require professional attention.
Start by unplugging the appliance and checking its condition. Then consult your model’s manual for specific guidance. If the error persists, contact Morphy Richards support or a qualified technician to determine the safest and most practical repair option.