In many cases, this error points to a problem with the temperature sensor. Although some basic checks can help you identify the issue, certain faults require professional repairs. Understanding what causes E2 will help you determine the safest way to get your air fryer working again.
—
What Does the E2 Error Mean on a Kent Air Fryer?
The E2 error on a Kent air fryer indicates a short circuit in the temperature sensor, according to the instruction manual for the Kent Digital Air Fryer 7L, model 116184. This sensor monitors the temperature inside the appliance and helps its electronic control system regulate heating.
During normal operation, the temperature sensor sends electrical signals to the control board. The board uses this information to manage the heating element and maintain the selected cooking temperature.
When the sensor develops a short circuit, its electrical readings may become unreliable. The air fryer can detect this abnormal condition and display E2 instead of continuing its normal operation.
You may notice that the appliance stops heating, refuses to begin cooking, or displays the error shortly after you connect it to power. However, the exact symptoms depend on your Kent air fryer model.
E2 is different from E1 and E3. On the Kent 7L model 116184, E1 indicates that the temperature sensor isn’t working, while E3 indicates overheating. E2 specifically identifies a sensor short circuit.
Because this fault involves the temperature monitoring system, it’s best to avoid using the appliance until the problem has been properly assessed.
Kent Air Fryer E2 Error: Common Causes
The E2 error generally points to an electrical problem involving the temperature sensor or its associated circuit. However, identifying the exact faulty component requires proper diagnosis.
Here are five possible causes and the signs that may help you recognize them.
1. Faulty Temperature Sensor
A defective temperature sensor is one of the most direct explanations for the E2 error. The sensor measures the temperature inside your air fryer and provides the information needed to control heating.
If the sensor develops an internal short circuit, the control board may receive an abnormal electrical reading. As a result, the appliance can display E2 and interrupt its operation.
Sensor problems can develop because of component defects, physical damage, or deterioration over time. Although temperature sensors are designed to operate in hot environments, they can still fail.
You might notice that E2 appears immediately after switching on the air fryer. In other cases, the appliance may operate briefly before displaying the error.
However, these symptoms don’t confirm that the sensor itself needs replacement. A damaged connection or another electrical fault can sometimes produce a similar reading.
2. Damaged Temperature Sensor Wiring
The temperature sensor connects to the air fryer’s electronic control system through electrical wiring. These connections allow temperature information to reach the control board.
If the wiring becomes damaged, the sensor circuit may malfunction. For instance, damaged insulation can allow wires or conductive parts to touch where they shouldn’t, potentially creating a short circuit.
This type of damage can result from manufacturing defects, excessive heat, physical stress, or deterioration inside the appliance.
A possible clue is an error that appears intermittently before becoming permanent. However, intermittent operation can also occur with other electronic faults.
Because the sensor wiring is located inside the appliance, checking it requires access to electrical components. A qualified technician should handle this inspection rather than having you remove the housing yourself.
3. Faulty Electronic Control Board
The electronic control board processes signals from the temperature sensor and manages the air fryer’s cooking functions.
If the part of the board responsible for reading the sensor develops a fault, the appliance may incorrectly interpret the temperature signal or detect an electrical problem.
Possible board faults include damaged circuits, failed electronic components, or defects affecting the sensor input.
An air fryer with this problem might display E2 immediately after receiving power, even before the heating element starts operating.
Still, the E2 code alone doesn’t confirm a faulty control board. Kent’s model 116184 manual identifies a temperature sensor short circuit but doesn’t specify whether the sensor, wiring, or controller is responsible.
A technician may need to test the sensor circuit and control board to distinguish between these possibilities.
4. Moisture Reaching Internal Electronics
Moisture can interfere with electrical connections and electronic components inside an air fryer.
Although the cooking basket is designed to handle food moisture, the appliance’s electrical housing shouldn’t be exposed to water.
Liquid spills, improper cleaning, or storage in damp conditions can allow moisture to reach areas where it may cause corrosion or electrical faults.
If E2 appeared after the appliance was accidentally soaked or exposed to a significant spill, moisture damage is worth considering.
You might also notice unusual display behavior or other electrical problems. However, these signs aren’t specific to moisture damage.
Even when the exterior feels dry, water or corrosion may remain inside. Therefore, an appliance suspected of having internal moisture damage should remain unplugged until it has been professionally assessed.
5. Heat Damage to Internal Components
Your Kent air fryer produces high temperatures during cooking, and its internal components are designed to operate within specified conditions.
However, excessive heat can damage wiring insulation, electrical connections, and electronic parts. If the affected component belongs to the temperature sensor circuit, an E2 error may develop.
Blocked ventilation openings, unsuitable placement, or an existing internal fault can contribute to abnormal heat buildup.
One possible sign is an appliance that develops errors after operating for some time. Nevertheless, this pattern doesn’t establish heat damage as the cause.
It’s also important to distinguish a sensor circuit fault from overheating. On the Kent 7L model 116184, E3 is the designated overheating error, while E2 indicates a sensor short circuit.
Kent Air Fryer E2 Error: How to Fix
Since E2 can involve the temperature monitoring circuit, repairing it may require replacing a damaged sensor or another internal component.
However, before arranging repairs, you can perform a few safe checks to confirm the model, identify visible damage, and determine the appropriate next step.
1. Switch Off and Unplug the Air Fryer
The first thing to do when E2 appears is stop using the appliance.
If the controls still respond, switch off the air fryer normally. Then remove the plug from the wall outlet, holding the plug rather than pulling the cord.
If the appliance was cooking when the error appeared, allow it to cool completely before touching the basket or other hot surfaces.
This prevents further operation while you investigate the fault.
Although disconnecting an appliance can clear some temporary electronic problems, unplugging won’t repair a genuinely shorted temperature sensor.
Avoid repeatedly restarting the air fryer or attempting to force it to continue heating.
If your particular model’s instruction manual provides a specific restart procedure for E2, follow that guidance. Otherwise, leave the appliance disconnected and arrange the recommended service.
2. Check Your Kent Air Fryer Model and Manual
Kent manufactures different air fryer models, so it’s important to confirm which one you own before following troubleshooting instructions.
You can usually find the model information on a label underneath or behind the appliance.
Make sure the air fryer is unplugged and completely cool before moving it.
Look for the model number, product code, and electrical specifications. These details will help you locate the correct manual.
For example, the Kent Digital Air Fryer 7L has product code 116184, and its troubleshooting guide identifies E2 as a short circuit in the temperature sensor.
Once you’ve identified your model, check the error code section of its manual.
If the manufacturer recommends professional service for E2, don’t attempt to clear the code by changing cooking settings or repeatedly disconnecting the power.
Temperature sensor faults generally cannot be corrected using ordinary cooking controls.
3. Inspect the Power Cord and Exterior for Damage
A visual inspection can help you identify obvious electrical hazards before arranging repairs.
Ensure the air fryer is unplugged, then examine the power cord and plug for signs of damage.
Look for cracked insulation, exposed wires, melted areas, or unusual discoloration.
Also inspect the appliance’s exterior for evidence of overheating or accidental water exposure.
If you notice burning marks, a damaged cord, or signs that liquid entered the electrical housing, don’t reconnect the appliance.
Keep in mind that a damaged external power cord isn’t an established cause of the E2 sensor error. However, identifying electrical damage is important for safe handling.
You should also confirm that the appliance’s electrical rating matches your power supply.
The Kent Digital Air Fryer 7L, model 116184, is rated for 230V AC, 50Hz, with a power consumption of 1500 watts. Other models may have different specifications.
Kent RO Systems
Never operate the appliance using an incompatible electrical supply or damaged adapter.
If the exterior appears normal, the E2 fault may still be present inside the appliance.
4. Check the Ventilation Openings
Adequate ventilation helps your air fryer release heat during cooking.
Although blocked vents aren’t a confirmed cause of E2, poor airflow can contribute to excessive heat around the appliance.
Before checking the vents, disconnect the power and allow the air fryer to cool.
Inspect the visible air inlet and outlet openings for dust, grease, or objects blocking airflow.
Remove any loose obstructions from accessible exterior surfaces. However, don’t insert tools into the openings or attempt to reach internal components.
For the Kent Digital Air Fryer 7L model 116184, the manufacturer recommends leaving at least 10 cm of free space behind, beside, and above the appliance.
If your air fryer is positioned directly against a wall or surrounded by other kitchen equipment, correct its placement before any future use.
You can also wipe accessible exterior surfaces with a soft, slightly damp cloth. Avoid allowing moisture into the electrical openings.
However, cleaning the vents won’t repair an existing temperature sensor short circuit.
If E2 is already displayed, follow the manufacturer’s service guidance rather than operating the appliance to see whether improved ventilation clears the fault.
5. Arrange a Warranty Inspection or Service Request
If your Kent air fryer displays E2, contacting the manufacturer is a sensible next step.
The error identifies a problem involving the temperature sensor circuit, which may require professional testing and replacement parts.
Before contacting customer support, gather the appliance’s model number, serial number if available, and proof of purchase.
Explain whether the error appeared immediately after switching on the appliance or during cooking. Mention any unusual smells, electrical damage, or previous exposure to water.
These details can help the service team determine the appropriate inspection.
If your appliance is covered by a manufacturer’s warranty, ask whether the fault qualifies for repair or replacement under its terms.
Kent’s warranty conditions vary by product, so check the documentation supplied with your particular air fryer rather than assuming every model has identical coverage.
For customers in India, Kent provides the following official service contacts.
-
Customer care: +91 92789 12345
-
Email: service@kent.co.in
-
Website: Kent Customer Service
Kent also offers online service request options.
Book Service, AMC and Support Online
Avoid opening the appliance before contacting customer service, particularly if it’s still under warranty.
6. Contact a Qualified Appliance Repair Technician
If the air fryer is outside its warranty period or manufacturer service isn’t available, contact a qualified appliance repair technician.
A technician can determine whether the E2 error originates from the temperature sensor, its wiring, or the electronic control board.
Depending on the diagnosis, the repair may involve replacing a defective sensor, correcting damaged electrical connections, or repairing an affected control component.
However, replacing the temperature sensor isn’t guaranteed to resolve E2 unless testing confirms that the sensor is faulty.
A qualified technician can perform the appropriate electrical checks and confirm that the temperature monitoring system operates correctly after repairs.
Avoid attempting to test sensor resistance, remove internal covers, or bypass temperature protection components yourself.
These tasks involve electrical systems that may remain hazardous even after the appliance has been disconnected.
If suitable parts are unavailable or the repair cost is close to the price of a replacement air fryer, purchasing a new appliance may be the better option.
Wrapping Up
The Kent air fryer E2 error generally indicates a short circuit in the temperature sensor circuit. Depending on the fault, the problem may involve the sensor itself, damaged wiring, or another internal electronic component.
Although checking the model number, power cord, and ventilation openings can help identify visible problems, these checks won’t necessarily resolve E2.
If the error appears, disconnect the air fryer and avoid further use until the fault has been assessed. Contacting Kent customer service or a qualified appliance technician is the safest way to arrange the correct repair.