Seeing the E1 error on your Morphy Richards air fryer can be frustrating, especially when the appliance suddenly stops heating or refuses to start. You may have already tried switching it off and back on, only to find the same warning on the display.
This error usually indicates a problem with the temperature sensing circuit. Although some basic checks may help identify the problem, certain faults require professional repair. Understanding what triggers E1 will help you determine the safest way to get your air fryer working again.

What Does Error E1 Mean on a Morphy Richards Air Fryer?
The E1 error on certain Morphy Richards air fryers indicates a broken or open circuit in the temperature sensor system. This means the electronic control board cannot receive the expected electrical signal from the sensor.
Your air fryer uses a temperature sensor to monitor the heat inside its cooking chamber. The sensor sends electrical information to the control board, allowing the appliance to regulate the heating element and maintain the temperature you’ve selected.
When the sensor circuit becomes disconnected or develops an internal fault, the control board may detect an abnormal reading and display E1. Depending on the model, the air fryer may stop heating, refuse to begin cooking, or continue showing the error whenever you switch it on.
For example, the Morphy Richards MRAFG55BK instruction manual identifies E1 as a broken thermal sensor circuit. However, error definitions can differ between models. This is why checking your specific instruction manual is essential before attempting any troubleshooting.
Morphy Richards Air Fryer Error E1: Common Causes
The E1 warning generally points to a problem involving the temperature sensing circuit on models that use this error definition. Several faults can interrupt the electrical connection between the sensor and the control board.
1. Faulty Temperature Sensor
A defective temperature sensor is one of the main possible causes of the E1 error on your Morphy Richards air fryer.
The sensor monitors changes in cooking temperature and communicates with the control board. If its internal electrical circuit breaks, the board may stop receiving valid temperature information. As a result, the appliance can display E1 and interrupt normal operation.
Temperature sensors can fail because of component deterioration, electrical damage, or exposure to conditions outside their intended operating range. However, normal cooking heat alone doesn’t establish that a sensor has failed.
You might notice E1 appearing immediately after switching on the appliance, even before it starts heating. In other cases, the warning may appear during cooking when a damaged component stops functioning correctly.
These symptoms suggest a problem with the sensing system, but they cannot confirm that the sensor itself needs replacement.
2. Loose Temperature Sensor Connection
The temperature sensor communicates with the control board through electrical connections inside the appliance. If one of these connections becomes loose or disconnected, the electrical circuit may remain open.
This can prevent the control board from receiving the information it needs to manage the heating system.
A loose connection may develop because of a damaged connector, an assembly defect, or deterioration over time. Physical damage to the appliance can also affect internal connections.
You may suspect a connection problem if E1 appears intermittently, although a defective sensor or damaged wire can produce similar behavior.
Since the affected connections are located inside the appliance, inspecting or repairing them requires professional attention. Attempting to open the housing yourself could expose you to dangerous electrical components.
3. Damaged Internal Wiring
Another possible cause of E1 is damaged wiring between the temperature sensor and the electronic control board.
These wires carry the sensor’s electrical signal. If a wire breaks or loses continuity, the control board may detect an open circuit even when the sensor itself is functioning correctly.
Wiring damage can result from excessive heat, mechanical stress, damaged insulation, or deterioration of electrical connections.
For example, if the appliance has been dropped or suffered physical damage, internal wiring could be affected. However, a visible mark on the exterior doesn’t necessarily mean the sensor wiring has been damaged.
The E1 warning may remain on the display until the interrupted connection is repaired. Because the wires are hidden inside the housing, proper diagnosis requires suitable electrical testing by a qualified technician.
4. Moisture Affecting Electrical Connections
Moisture entering the electrical housing can interfere with the air fryer’s electronic components.
Although the cooking chamber is designed to handle moisture released from food, the internal control board and electrical connections must remain protected from liquid.
If water enters the housing during cleaning or after a spill, it may damage connectors or contribute to corrosion. Over time, corrosion can interfere with electrical continuity and potentially cause an open circuit.
You might suspect moisture damage if E1 appeared after liquid was spilled near the control panel or the appliance was cleaned improperly.
However, moisture exposure is only a possible contributing factor, not a confirmed explanation for every E1 warning. The error code alone cannot identify water damage.
If liquid has entered the electrical housing, stop using the appliance and arrange professional assessment.
5. Faulty Electronic Control Board
The electronic control board manages the air fryer’s heating functions and interprets information from the temperature sensor.
If the board’s temperature sensing circuit develops a fault, it may fail to recognize a valid sensor signal. This can potentially produce an E1 warning even when the sensor and its wiring are intact.
Circuit board problems may result from damaged electronic components, electrical faults, or moisture exposure.
A defective control board may also cause other operating problems, such as unexpected shutdowns or unusual display behavior. However, these symptoms aren’t specific enough to confirm a board failure.
A technician must determine whether the problem originates from the sensor, its connections, or the control board before deciding which component requires repair or replacement.
Morphy Richards Air Fryer Error E1: How to Fix
Since E1 may indicate a broken temperature sensor circuit, the safest troubleshooting methods involve checking the appliance’s condition and following its manual. Basic checks can help rule out obvious external problems, but they cannot repair an internally damaged sensor or wire.
1. Switch Off the Air Fryer and Let It Cool
When E1 appears, start by switching off your Morphy Richards air fryer and disconnecting it from the electrical outlet.
If the appliance stopped during cooking, allow it to cool completely before handling the cooking basket or removable accessories.
Don’t continue pressing the start button or repeatedly attempting to run another cooking program. If the temperature sensing circuit isn’t functioning correctly, the appliance may be unable to monitor its cooking temperature reliably.
While the air fryer cools, take note of when the error appeared.
For example, determine whether E1 appeared immediately after plugging in the appliance, when you selected a cooking program, or after the heating element had been operating.
This information can help a technician understand the circumstances surrounding the fault.
If the appliance produces smoke, sparks, a burning smell, or unusual heat, avoid restarting it. Seek professional assistance instead.
2. Try a Power Restart if Your Manual Permits It
A power restart may help clear a temporary electronic display problem. However, it cannot repair a broken temperature sensor, disconnected wire, or faulty circuit board.
Some Morphy Richards manuals direct users to customer support when E1 appears. If your model’s instructions require professional assistance, follow that guidance rather than attempting a restart.
Where a restart is permitted and there are no signs of electrical damage, follow these steps.
- Switch off the air fryer and unplug it.
- Allow the appliance to cool completely.
- Check that the exterior, plug, and power cord are dry and undamaged.
- Reconnect it to a suitable electrical outlet.
- Observe whether E1 returns without starting a cooking cycle.
If the error appears again, unplug the appliance and stop testing it.
If the warning disappears, it doesn’t necessarily mean the underlying problem has been resolved. Intermittent electrical faults can temporarily stop producing an error.
Contact the manufacturer for guidance before returning the appliance to normal cooking use.
3. Inspect the Power Cord and Electrical Outlet
Although the E1 code generally concerns the temperature sensing circuit, checking the external power connection can help identify other electrical problems.
Start by examining the power cord and plug while the air fryer is unplugged.
Look for damaged insulation, exposed wiring, burn marks, melted plastic, or other visible signs of deterioration.
Also, inspect the wall outlet for discoloration or damage. Don’t touch damaged electrical contacts or attempt to repair the outlet yourself.
A damaged external power cord isn’t an established cause of the E1 sensor error. However, it can create a separate electrical hazard that needs attention.
If the power cord is damaged, arrange replacement through the manufacturer or a suitably qualified professional.
If everything appears normal, continue by checking your model’s instructions rather than assuming the external power supply is responsible for E1.
4. Check for Moisture and Clean the Accessible Components
If E1 appeared shortly after cleaning the appliance or spilling liquid nearby, inspect the accessible areas for signs of moisture.
First, unplug the air fryer and make sure it has cooled completely.
Remove the cooking basket, drawer, or glass bowl according to your model’s instructions. Look for water or food residue around the removable components and accessible surfaces.
If cleaning is needed, follow these steps.
- Remove food particles from the cooking container.
- Wash removable accessories using the method recommended in your instruction manual.
- Wipe permitted exterior surfaces with a soft, slightly damp cloth.
- Dry the removable components thoroughly.
- Check for visible liquid near the electrical housing or control panel.
Never immerse the main appliance housing in water or spray liquid into its ventilation openings.
If you suspect that water has entered the electrical housing, leave the appliance unplugged. Don’t attempt to dry its internal electronics with a hair dryer or other heating device.
Cleaning the removable parts is useful maintenance, but it won’t repair a broken sensor circuit. If E1 has appeared, follow the manufacturer’s instructions before using the appliance again.
5. Check Your Model Number and Warranty
Before purchasing replacement parts or arranging repairs, identify your Morphy Richards air fryer model.
You can usually find the model number on a rating label attached to the underside, rear, or base of the appliance. It may also appear on the original packaging or instruction booklet.
Once you have the model number, locate the corresponding instruction manual.
For example, the Morphy Richards MRAFG55BK manual identifies E1 as a broken thermal sensor circuit and recommends contacting Customer Care.
Meanwhile, the MRAF72BK manual describes E1 and E2 as circuit alarm faults and directs owners to return an affected appliance to the place of purchase if it is under warranty.
These differences make it essential to follow the instructions intended for your specific model.
If your appliance is still covered by warranty, contact the retailer or manufacturer before arranging a third party repair.
Have your purchase receipt, model number, and a description of the error ready. This can help the support representative determine the appropriate next step.
6. Contact a Qualified Appliance Technician
If E1 persists or returns, the appliance may have an internal fault that requires professional diagnosis.
A qualified technician can assess the temperature sensing circuit to determine whether the problem involves a defective sensor, broken connection, damaged wiring, or electronic control board.
Depending on the findings, repairing a connection or replacing a faulty component may restore normal operation.
However, parts availability and the air fryer’s design can affect whether repair is practical.
If the appliance is under warranty, contact Morphy Richards or the authorized support provider first. Opening the housing or attempting unauthorized repairs may affect warranty coverage.
For an appliance outside its warranty period, ask for a repair estimate before approving the work.
If the repair costs almost as much as a replacement unit, purchasing another air fryer may be the more practical choice.
Avoid buying replacement sensors or circuit boards based solely on the E1 warning. Proper diagnosis helps prevent unnecessary spending and ensures that the actual fault is addressed.
Wrap-Up
The Morphy Richards air fryer E1 error usually indicates a problem with the temperature sensing circuit on models that use this code. A damaged sensor, loose connection, broken wire, or faulty control board may be responsible, but the warning alone cannot identify the exact component.
Start by switching off the appliance, allowing it to cool, and checking your model’s instructions. If a safe restart is permitted, you can try it once. However, if E1 persists or returns, contact Morphy Richards support or a qualified technician for proper diagnosis and repair.